MicroE Systems Mercury 1000 Instalační manuál

Procházejte online nebo si stáhněte Instalační manuál pro ne MicroE Systems Mercury 1000. MicroE Systems Mercury 1000 Installation manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 14
  • Tabulka s obsahem
  • ŘEŠENÍ PROBLÉMŮ
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Mercury
1000V - Vacuum Rated
AAnnaalloogg OOuuttppuutt EEnnccooddeerr SSyysstteemm
IInnssttaallllaattiioonn MMaannuuaall
aanndd RReeffeerreennccee GGuuiiddee
Manual No. IM-M1000V Rev S5
Zobrazit stránku 0
1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - 1000V - Vacuum Rated

Mercury™1000V - Vacuum RatedAAnnaalloogg OOuuttppuutt EEnnccooddeerr SSyysstteemmIInnssttaallllaattiioonn MMaannuuaall aanndd RReeffeerreennccee

Strany 2 - PPaatteennttss

Reference SectionInstallation of Linear Scales Page 8MicroE SystemsL0.2L0.6L0.2LBenching pinsPositioning the ScaleNote: Before beginning mount

Strany 3

Page 9Installation Reference GuideMercury encoders require a minimum of 4.75V DC continuously. When designing circuits and extension cables to use Me

Strany 4 - SSyysstteemm VViieeww

Page 10Customer Interface Cable RequirementsCustomer cables that interface to Mercury series encoders must have the following characteristics:• Twis

Strany 5

TroubleshootingProblemThe Power/Calibration indicator will not come on.Solution• Make sure the M1000 15-pin D connector is fully seated and connected.

Strany 6 - Installation Instructions

World Headquarters: 125 Middlesex Turnpike • Bedford • MA 01730 USAwww.microesys.com • [email protected] • T. [781] 266-5700 • F. [781] 266-

Strany 7 - M1000V, producing a

IInnttrroodduuccttiioonnMicroE Systems was founded to advance encoder technology toa level never before achieved. Our objective was to design encoders

Strany 8

TTaabbllee OOff CCoonntteennttssSYSTEM ILLUSTRATION PAGEEncoder with Linear scale 2Encoder with Rotary scale 3INSTALLATION INSTRUCTIONSEncoder Syste

Strany 9

Mercury 1000V Analog Encoder System with Linear scaleEExxppaannddeedd VViieewwEnd locator pinMounting screws & flat washers (2needed per screw)Br

Strany 10 - Reference Section

Mercury 1000V Analog Encoder System with Rotary scaleEExxppaannddeedd VViieewwDouble shielded cableTop reflective rotary scaleRotary glass scale sens

Strany 11 - Installation Reference Guide

Installation InstructionsLinear Encoders12Attach the scale to the base slide. Reference the preferreddatum on the interface drawing for either end or

Strany 12 - Shield Termination:

Installation InstructionsLinear EncodersProper sensor alignment may require minor adjustments to the sensor position withrespect to the scale. This ca

Strany 13 - Troubleshooting

Installation InstructionsRotary EncodersAttach your hub/scaleassembly to the rotarydevice. Refer to theinterface drawing. Thereflective surface of the

Strany 14 - Contacting MicroE Systems

IIMMPPOORRTTAANNTTOOUUTTPPUUTT CCAALLIIBBRRAATTIIOONN PPRROOCCEEDDUURREEThis procedure must be completed forproper system operation each time thesen

Komentáře k této Příručce

Žádné komentáře